How to Make a Popsocket Sticky Again After Removing

Download Commodity

Download Article

PopSockets are very useful for getting a better grip on your phone, but they can get dirty with time and the adhesive that sticks it to the back of your phone can become loose and lose its stickiness. Afterward removing it from your phone, merely soak it in water and scrub it with soapy h2o your PopSocket to make it look good as new and stick as if y'all bought it yesterday.

  1. ane

    Fill a shallow dish with cold tap water. Grab a shallow dish, such as a small basin or a deep plate, and make full it with about .five in (i.3 cm) of very cold tap water. This is to ensure that you just soak the adhesive side of the PopSocket — y'all should clean the plastic grip separately.

    • Even if your PopSocket is larger than normal, using just a .5 in (1.3 cm) layer of water volition ensure that only the agglutinative side touches the water when information technology is extended.
  2. 2

    Remove the popsPopSocketocket and place it sticky-side down in the water. Dig your fingernail under the PopSocket to pry it off of your telephone, then pull the plastic grip to it extend to its full length. Place the agglutinative side down in the water and so the plastic grip pokes in a higher place the surface of the water.

    • Exist certain that your extended PopSocket rises above the surface and drain out h2o as necessary to avoid getting the residual of it wet.[i]

    Advertisement

  3. 3

    Permit the PopSocket soak for well-nigh 10 seconds, and then remove information technology. Don't disturb the water and don't have information technology out before 10 seconds are up. In one case 10 seconds take passed, quickly take it out of the water past the grip and milkshake off whatsoever excess water. Practise non permit it soak for more than 10 seconds or it could ruin the adhesive. [2]

    • If yous are concerned nigh ruining the adhesive, run the PopSocket under cold water for a few seconds instead, although soaking it is more constructive.[3]
  4. four

    Lay a newspaper towel down and identify the PopSocket sticky-side up. Y'all can use a regular kitchen towel or a linen towel, depending on what you have readily available. Lay the PopSocket with the sticky side pointing up and the blueprint and plastic grip touch the paper.[four]

  5. v

    Allow the adhesive side of the PopSocket dry for ten minutes. Leave your PopSocket to dry for 10 minutes at most, and keep an eye on it as it dries to see if it finishes sooner.[5] Avoid using a hair dryer or dabbing it with a towel or you could damage the adhesive and arrive less viscous. But permit it air dry, and swiftly re-attach information technology to your phone the moment it is dry by pressing the gummy side firmly onto the dorsum of your phone.

    • Practice not let your PopSocket dry out for more than 15 minutes at most or it may lose its power to stick.
    • If y'all accidentally leave information technology out, run it under cold water for a few seconds and so let it dry again, although be aware that it may not regain its stickiness.

    Advertisement

  1. 1

    Remove any additional stickers yous've added to the end of the PopSocket. If you lot added stickers to the PopSocket's grip, you will need to remove them before you clean information technology. If the adhesive is even so practiced on the sticker feel free to put information technology dorsum on after cleaning, otherwise you volition have to but throw it away and find a new ane.

    • Popsockets normally come with some kind of blueprint on the finish of the grip, so even if you accept to remove any additional stickers you've added, it will however have an aesthetic blueprint.[6]
  2. two

    Remove the PopSocket and run the plastic grip under common cold water. Use your fingernail to pry the PopSocket off of your telephone, then hold the adhesive side of the PopSocket and turn your water faucet to a low flow on cold. Run merely the plastic grip of the PopSocket under h2o — if you must, wrap the adhesive in a hand towel to prevent getting information technology wet and affecting its stickiness.

    • You tin can clean the agglutinative separately, simply if you get it moisture before you're set to clean it, y'all could cause the adhesive to lose some of its stickiness. Wrap it or take intendance to non get information technology wet while cleaning the grip.
  3. 3

    Scrub the plastic grip with the corner of a soapy rag, fugitive the adhesive. Hold the PopSocket by the mucilaginous side again and scrub the plastic grip with the corner of a soapy rag PopSocket. Have care to avoid getting lather on the adhesive, and only scrub the plastic parts of the PopSocket.

    • Scrub inside the grooves of the PopSocket'south expandable middle section with a cotton swab soaked in soapy water.
    • Apply seventy percent rubbing booze to specially stubborn stains or grime with a cotton wool swab, then rinse information technology nether water once more. Rubbing alcohol is smashing for removing stains equally it evaporates quickly and leaves no harm.
  4. 4

    Rinse the grip once once more, then dry it with a paper towel or rag. Run the grip nether h2o to go rid of soapy balance and rubbing alcohol, over again taking care to avoid getting the adhesive moisture. Then, take a dry rag or a paper towel and dab the PopSocket dry until information technology is completely gratuitous of water.[7] Printing it firmly onto the back of your telephone with the viscous-side down.

    • You can also air dry out the plastic grip. Expand the PopSocket then balance it on its side on a newspaper towel. This prevents the adhesive from sticking to the towel and will still allow the grip to air dry and drip dry.

    Advertisement

Ask a Question

200 characters left

Include your email address to get a bulletin when this question is answered.

Submit

Ad

  • After re-attaching the PopSocket to your telephone, await at to the lowest degree 1 hour before yous extend the grip and use it. This allows enough time for the adhesive to fully stick to your phone, reducing the take a chance of it detaching suddenly.[8]

Thanks for submitting a tip for review!

Advertizement

  • Avoid using rubbing alcohol in a airtight room, and take the PopSocket to a well-ventilated surface area to forbid inhaling rubbing alcohol fumes.

  • Never let the gummy side of the PopSocket be exposed to air for more than 15 minutes, fifty-fifty when cleaning the plastic grip, equally this destroys the adhesive.

Advertising

Almost This Article

Cheers to all authors for creating a page that has been read 29,159 times.

Is this commodity up to date?

chapmangrell1984.blogspot.com

Source: https://www.wikihow.com/Clean-a-PopSocket

0 Response to "How to Make a Popsocket Sticky Again After Removing"

Post a Comment

Iklan Atas Artikel

Iklan Tengah Artikel 1

Iklan Tengah Artikel 2

Iklan Bawah Artikel